How To Replace A Shattered Screen on iPhone 6/6s

Almost every smartphone owner has at some stage dropped one of their phones and broken the screen. A replacement by the manufacturer costs a fortune but it is actually quite simple to replace yourself. You can buy a replacement for your phone through a number of online stores, eBay has a large number of electronics suppliers which stock replacement parts.

This guide shows you the step by step process to replace your iPhone screen yourself. Although this change is performed on an iPhone 6, the 6s is almost exactly the same.

Scroll down to the bottom of the page for a full video of the change being done on an iPhone 6.

What You Will Need To Replace Your iPhone 6 Screen

  • Replacement Screen – Buy Screen & Tool Set
  • Pentelobe Screwdriver
  • Small Star/Philips Screwdriver
  • Prying Tool
  • Screen Prying Tool
  • Screen Puller

If you look around online, most of the suppliers which stock replacements will add a small toolset (pictured in the video and cover picture) for a small fee or even for free, it is worthwhile getting the toolkit.

How to Replace your iPhone Screen

Replacing your iPhone screen is done in four stages, first you will remove the old one, then remove all of the components from the old one, install them on the replacement screen and finally install and connect the replacement to your iPhone.

It is worthwhile keeping a piece of paper and a pen handy to make a sketch of the inside of the phone and which screws your have removed from where. The screws are all different sizes and lengths and need to go back into the same hole you removed them from. Rather spend a bit more time taking the phone apart and keep track of the components, it will make your life a lot easier when putting it back together.

Removing the Broken Screen

First start by switching your iPhone off, this ensures that you don’t short circuit anything when clipping and unclipping connectors.

switch the phone off

Now use the pentelobe screwdriver in your toolkit to remove the two screws at the bottom of you phone.

remove the pentelobe screws

Once the screws have been removed, pry the screen away from the body. If it is not totally shattered, using the pulling suction cup to help you lift the screen from the body of the phone. The  prying tool helps to slot in between the screen and the body and pull it away.

pry the screen away from the body

Near the top of the phone, there is a silver cover plate which keeps the connectors locked in place. Unscrew and remove the screws and the cover plate.

unscrew the connector cover plate

Now use the smaller prying tool to unclip the four connectors on the ribbon cables. These connectors snap into place much like Lego’s. Once the ribbon cable connectors are unclipped, you can remove the screen from the body of the phone.

unclip the ribbon cable connector

Remove the Components from the Old Screen

The replacement you have bought will most likely come without any of the additional electronic components mounted onto it, you will have to move these across from your old screen onto your new screen.

First start by removing the camera, sensor and earpiece. Remove the screws and cover plate which secure the camera.

remove the camera cover plate

Now remove the camera, sensor and ear piece, they should come away easily with the cover plate removed.

remove the camera, sensor and earpiece

You need to remove the screws to the silver cover plate on the back, this houses the ribbon cable to the fingerprint sensor and home button. Remove the screws around the perimeter of this cover, the cover will remain in place until the fingerprint sensor is removed.

remove the screen plate screws

Next, remove the cover plate over the fingerprint sensor.

remove the fingerprint sensor screws

Unclip the connector to the fingerprint sensor ribbon cable, this is the same type of connector used to clip the other ribbon cables and it just snaps off using the prying tool.

unclip the fingerprint ribbon connector

Now you can remove the fingerprint sensor. It is stuck on by its rubber mounting which is sticky on one side. Simply pull it off with your fingers or with a flat screw driver. It should still be sticky enough to stick onto the replacement.

remove the fingerprint sensor

Lastly, unclip the fingerprint sensors electronics which are held in place with a small white peg. Use the prying tool to lift it off of the peg.

remove the sensor ribbon cable

Now you can remove the back cover plate.

remove the screen coverplate

The last items to remove are the small plastic locators for the camera and for the sensor near the earpiece. Remove these with a tweezer or small screwdriver.

remove the plastic locators

Install the Components on the New Screen

Installing the components on the replacement is quite easy once you know how they came off the old one, just follow the steps in reverse.

First replace the plastic locators for the camera and sensor.

reinstall the locators and components

Now replace the camera and sensor. The small white pegs act as a location guide and the components fit into the plastic locators.

use the pegs as a guide

Replace the earpiece and then screw the silver cover plate back into place.

replace the coverplate

Next, stick the fingerprint sensor onto the replacement with the sticky side of the rubber mounting. Clip the electronics in place over the white plastic peg.

stick the sensor in place

Clip the ribbon cable connector in.

reclip the ribbon connector

Now replace the fingerprint sensor cover plate and screw in the screws.

replace the sensor coverplate

Replace the cover plate and screw in the screws around the perimeter.

replace the screen coverplate screws

The replacement is now ready to be reinstalled on the body of the phone.

Install The New Screen

Start installing the new screen by clipping in the four ribbon connectors. Each one is a different size and shape so it should be easy to see which one goes where.

clip in the ribbon cable connectors

Fold the screen down gently and rest it on top of the body. Now you should check that everything which you have connected is working correctly. Power on the phone and make sure that it displays correctly, the touch sensor works, the fingerprint sensor and home button work as well as the front camera alignment. If anything doesn’t work then it is likely due to a fault in the ribbon cable connections, try unclipping and reconnecting them.

power on the phone to check that everything works

Once everything works, turn the phone off again and then begin securing the screen. At the top are two plastic clips which slide into the body of the phone. It can then be pressed into place from the top down.

snap the screen back into place

Snap the bottom into place and align the screw holes. Finally slide the pentelobe screws in and screw them in.

snap the bottom into place and replace the screws

You have now successfully replaced your phone screen!

the fixed phone

Power the phone back on and it is ready to use again.

power the phone back on

If you enjoyed this post, have a look at these 5 Secret iPhone Codes You Didn’t Know About or find out how to Charge your iPhone Battery the Right Way.

iPhone Screen Replacement Video

Share this repair:

how to replace an iphone screen

Michael Klements
Michael Klements
Hi, my name is Michael and I started this blog in 2016 to share my DIY journey with you. I love tinkering with electronics, making, fixing, and building - I'm always looking for new projects and exciting DIY ideas. If you do too, grab a cup of coffee and settle in, I'm happy to have you here.

3 COMMENTS

  1. Help! Can you tell me what I did wrong? I did everything you did have the same tools. When I get to connecting the cables to check if the power works it won’t turn on. I think I mixed up some of the screws could that be why? I don’t know. If you know why it wouldn’t be turning on that would be awesome.

    • Hi Jay,

      Sorry to hear you haven’t come right. I doubt that mixing up the screws would cause the screen not to come on, the pieces would just not fit that well together anymore. I would say that most likely one of the connectors is not seated properly or not contacting properly. Try reversing your steps and taking it all apart again and then putting it back together and see if that helps. If that doesn’t work, try fitting the old screen again just to check that nothing is wrong with the motherboard. If the old screen still works then you probably just have a faulty replacement screen, this is not that uncommon. Just send it back to the supplier and request a new one, they are usually pretty happy to help.

  2. Hi,
    I really like your photos. your presentation simply super.
    Thanks for sharing such great information. It is very informative and provides knowledge of Mobile Screen Repairing.

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Latest posts

Which NVMe Hat Is The Best For A Raspberry Pi 5

If you don’t know already, I’ve been selling these 3D printed cases for Raspberry Pi’s online for a few years now. With the launch...

Track Aircraft In Real-time With Your Raspberry Pi Using The FlightAware Pro

Have you ever seen a flight overhead and wondered where it is going? Or seen a unique-looking aircraft and wondered what type or model...

Pi 5 Desktop Case For NVMe Base or HatDrive! Bottom

Today we're going to be assembling a 3D-printed case for the Raspberry Pi 5 and Pimoroni's NVMe Base or Pineberry's HatDrive! This is an...

Related posts