Carving A Pumpkin for Halloween, Get It Right First Time

Let’s be honest, your Halloween decorations aren’t complete without a carved pumpkin. Carving a basic face into a pumpkin is actually quite easy and doesn’t take more than half an hour to do. They key is to get it right the first time and this is made easy by using a marker to draw on the pumpkin before you start cutting. So grab a pumpkin, a marker and a knife and lets get started.

What You Will To Carve Your Pumpkin

  • A Pumpkin (Obviously), Bigger Is Better
  • A Marker Pen
  • A Small Sharp Knife
  • Two or Three Tealight Candles

Carving Your Pumpkin

draw your design onto the pumpkin

Firstly you need to draw on your design, there are literally hundreds of ideas on sites like Flickr and Pinterest, a quick search and you’ll have an idea of what you want to carve. Now you need a bit of an artistic touch, draw an outline of the design you wish to carve onto your pumpkin, the nice thing about this method is you can wipe it off and make any changes quickly and easily without messing up your pumpkin. It also doesn’t matter if you have a few sketch lines or crossed out lines as we’ll wipe them off afterwards anyway.

Once you have your design drawn on, grab a knife, we need to cut the lid and hollow out the pumpkin. Begin by cutting a circle around the stem of the pumpkin (you can also draw on a circle to guide you) about 10cm (4″) in diameter is fine. Cut lightly at first to mark out your circle and then cut deeply towards the centre of the pumpkin going around the stem. Eventually, if you have cut deep enough all the way around, you’ll be able to pull the “lid” off. Cut the bottom of the lid square and put it aside.

The inside of the pumpkin should already be mostly hollow but it will be stringy and full of pips. Using your hand, pull all of the stringy bits and pips out. You can also use a spoon to really clean up the sides and the bottom well. Scrap as much as you can off without digging into the meat of the pumpkin.

carving-the-pumpkin

Now its time to get carving. Using your sharp knife, carefully cut along your marked lines. Make shallow cuts initially and slowly get deeper and deeper to ensure that you don’t slip and cut yourself or the wrong part of your pumpkin. Once you have cut a shape along all of its sides, it should be relatively easy to push into or pull out of the pumpkin depending on the angle you held your knife. Wiggle the bits around to see where more cutting is required.

the carved pumpkin

Once you have rough carved your pumpkin, do the finer details and clean up any rough or unclean edges. Once you are happy with your design, it is time to wipe off the marker. The marker should come off with a bit of soap and a cloth but if it is a bit more permanent then you may have to use some nail polish remover and cotton wool to wipe it off.

pumpkin-outside

Your pumpkin is now ready to put on display. Just before it gets dark, place two or three tea light candles into the centre and light them. Put the lid back on and your pumpkin is ready to use. The glowing grimace of a jack o lantern is sure to attract attention on your doorstep or down the driveway!

pumpkin-at-night

Have you carved a pumpkin his Halloween? Send us your pictures using the mail link above and we’ll add them to our page or let us know your tips and tricks in the comments section below.

There’s nothing like carving a pumpkin to get you craving a home baked pumpkin pie, try this great recipe to fill your home with the fresh pumpkin spice fragrance.

 

Michael Klements
Michael Klements
Hi, my name is Michael and I started this blog in 2016 to share my DIY journey with you. I love tinkering with electronics, making, fixing, and building - I'm always looking for new projects and exciting DIY ideas. If you do too, grab a cup of coffee and settle in, I'm happy to have you here.

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Latest posts

Which NVMe Hat Is The Best For A Raspberry Pi 5

If you don’t know already, I’ve been selling these 3D printed cases for Raspberry Pi’s online for a few years now. With the launch...

Track Aircraft In Real-time With Your Raspberry Pi Using The FlightAware Pro

Have you ever seen a flight overhead and wondered where it is going? Or seen a unique-looking aircraft and wondered what type or model...

Pi 5 Desktop Case For NVMe Base or HatDrive! Bottom

Today we're going to be assembling a 3D-printed case for the Raspberry Pi 5 and Pimoroni's NVMe Base or Pineberry's HatDrive! This is an...

Related posts